Each driving procedure must be carried out, maintaining the standard test form of the execution of each test. The Equalizer Circle Lab shows accurate analysis especially data performance. Therefore it is a more accurate diagnosis than the results of these tests. Since special conditions can affect its level, it cannot work properly. This means a reduction in incorrect test results, which is negligible. This is why it is important to ensure that the expected behaviour of these tests is fulfilled in terms of preparation.
How to test and remove it?
You should test that the temperature control line is in the correct position. Otherwise, you need to fix the vertical balance switch. Impedance probes that match the probe before using its impedance should be part of their conversion. There is a variable capacitor at one end of the probe near the oscilloscope. A few of the reviews may also have the ability to change that aspect of the review. It is used to adjust the impedance matching of the oscilloscope probe. If it fits, the measured waveform will be distorted.
The waveform of the heat cycle test determines whether you are doing the right amount of damage. Ideally, you should use this X10 review. So, there will be no more problems.
How to adjust the temperature of the thermal cycle laboratory?
The temperature in the test room temperature cycling refers to the process in which the room temperature is gradually reduced and stabilized at the specified temperature after the initial operation when the room is higher than the temperature of 3 ° C.
The temperature controller corresponds to a constant ± 3°C or determines the range of the temperature cycling test chamber from the temperature of the test stage. For example, the temperature range of 0 to 100C will not exceed 2 °C. Exceeding 100 ℃ or more will not exceed 2% of the rating. The control tool for this application is easy to see the correctness of the adjustment control. It has the functions of automation, program calculation, and the storage of parameters of historical data and parts.
Once the temperature exceeds the normal range, it is important to contact the manufacturer for immediate correction. Otherwise, you can ask a third-party metrology company to make the change. When the temperature is too high, the equipment and the manufacturer’s production process of this temperature system affect the laboratory which is not suitable.
Are you stuck on the wrong water system error while running a heat cycle lab?
We often divide water system errors due to water damage and water scarcity. First, we look at water leaks. Water leaks are mainly caused by water ball holes and water leaks in the thermal cycling test chamber.
The water ball pit is under the water ball bed. Under these conditions, it is expected that the soil is not good, causing the water in the side to flow in the water ball. It requires the adjustment of the horizontal plane of the ground. This situation should be considered in the water supply of the humidity laboratory. There is a water inlet valve installed on the water source and the water tank. The intake valve was probably opened relatively wide. You can try to correct the proximity of the test gear intake valve. If you still find that the water line is leaking, it may be due to water in the water tank and water line. The correction of this deficiency can be solved directly with the associated joint function.
Set the minimum temperature of the temperature cycle laboratory
Various reasons can cause internal failure and interfere with the investigation so that it cannot be completed properly. First, determine if the refrigeration compressor of the temperature cycling test room can start during the running time. It shows that the power source is stable. There was no problem with the electricity, but the various systems started to diagnose the system and continued to check the refrigeration system.
Two different types of compressors should be investigated and the pressure values of this reduced temperature compressor should be checked. If you find a fault, it means that the damping of the cooling system is not enough. It will be on hand to test the room temperature of the exhaust and the water line of the R23 compressor of the same distributor. If the exhaust tube temperature is not high, the intake tube is not low, this is a significant indication of the lack of refrigerant.
In the case of severe cooling, the 2 units work at the same time and heat to maintain the first part of the condition. If these two groups work together, this shows that the heat has stopped. The auxiliary unit will stop working and let others maintain the temperature of the guest group to keep the room cool. Without a single reception or heating effect, the air temperature of the laboratory cycle temperature will gradually increase. If its temperature rises to a certain level, the system of care will start its auxiliary process. By repeating this process, you can solve the temperature instability situation.
Conclusion
Test equipment and other products have significant differences, especially testing, testing equipment and test equipment used for testing. The accuracy of the test information is related to the calibre of the equipment. Therefore, the accuracy of the equipment and the stability of their test results are the main types of gear performance tests. Testing equipment such as the performance of a cycling test facility does not depend on the number of test items. It is the validity of the research and the consistency of the research results.
